 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ver. 1.0 specification for lcd module model no. tm128160ekfwg prepared b y : date: checked b y : date: verified b y : date: approved by: date: tianma microelectronics co., ltd
1/22 ver 1.0 revision record date ver. ref. page revision no. revision item 2/22 ver 1.0 1. general specifications: 1.1 display type: color stn 1.2 display color* 1 : display color: 65k color background* 2 : black (red, green, blue dots are off state) 1.3 polarizer mode: transmissive/negative 1.4 viewing angle: 6:00 1.5 driving method: 1/160 duty 1/5 bias 1.6 backlight type: led (3 lamps) backlight color: white 1.7 controller: s6b33b0a-b0cy 1.8 data transfer: 8 bit parallel 1.9 operating temperature: -20----+70 ?? storage temperature: -30----+80 ?? 1.10 vbat supply voltage: vbat= 3.2~4.5v 1.11 lcd operating voltage: vlcd= 16.8v 1.12 outline dimensions: refer to outline drawing on next page 1.13 dot matrix: 128 x 3 (rgb) x 160 dots 1.14 dot size: 0.227(r+g+b) ? 0.215(mm 2 ) 1.15 dot pitch: 0.237 ? 0.225 (mm 2 ) 1.16 weight: tbd * 3 * 1 color tone is slightly changed by temperature and driving voltage. * 2 color tone will be changed by backlight. * 3 tbd: to be determined. 3/22 ver 1.0 2. outline drawing 4/22 ver 1.0 3. lcd module part numbering system tm 128160 e k f w g ic package g: cog temprature range w: wide temperature range backlight type f: transmissive, led backlight lcd type k: color stn mode negative module series module type digits indicating: 128 (rgb) columns x 160 rows t: tianma m: module 5/22 ver 1.0 4. circuit block diagram 6/22 ver 1.0 5. absolute maximum ratings ta= 25 ?? item symbol min. max. unit remark power supply voltage v dd - v ss -0.3 +4.6 lcd driving voltage v lcd -0.3 +20.0 v operating temperature range t op -20 +70 storage temperature range t st -30 +80 ?? no condensation 7/22 ver 1.0 6. electrical specifications and instruction code 6.1 electrical characteristics v dd = 3v ? vss= 0v , ta= 25 ?? item symbol min. typ. max. unit supply voltage (logic) v bat -vss +3.1 +3.8 +4.5 v supply voltage (lcd drive) v lcd - 16.8 - v high v ih ? v dd =3.0 ? 0.8v dd - v dd v input signal voltage low v il ? v dd =3.0 ? 0 - 0.2 v dd v supply current (logic) i dd (v dd - v ss =3.0v) - - 2.5 ma operating current i op - - 60 ma oscillator frequency range f osc 220 - 330 khz supply voltage (led) v led - 9.9 - v supply current (led) i led 15.0 20.0 ma 8/22 ver 1.0 6.2 interface signals pinno. symbo l level description 1 vbat h power supply 2 vbat h power supply 3 gnd l ground 4 led-g h/l green led control pin 5 led-b h/l blue led control pin 6 led-r h/l red led control pin 7 disp-cs-sub h/l nc 8 rd h/l read operation(8080 system) 9 led-sub-en h/l led brightness select pin (half current work) 10 on-off h/l vdd on or off. h: active 11 disp-rst h/l reset pin l: active 12 led-main-en h/l led brightness select pin (full current work) 13 vibrator h/l vibrator control pin. 14 wr h/l write operation(8080 system) 15 disp-cs-main h/l lcd chip select pin 16 db0 h/l data bus bit 0 17 db1 h/l data bus bit 1 18 db2 h/l data bus bit 2 19 db3 h/l data bus bit 3 20 db4 h/l data bus bit 4 21 db5 h/l data bus bit 5 22 db6 h/l data bus bit 6 23 db7 h/l data bus bit 7 24 rs h/l index select/data command select 25 gnd l ground 26 gnd l ground 27 rec+ h/l receive input pin(+) 28 rec- h/l receive input pin(-) 29 sp+ h/l speak input pin(+) 30 sp- h/l speak input pin(-) 9/22 ver 1.0 6.3 interface timing chart read / write characteristics (8080 - series mpu) db 0 to db 7 (write) db 0 to db 7 (read) t dh80 t od80 t ds80 t acc80 0.9v dd 0.1v dd t pw l 80(r) , t pw l 80(w) t cy80 t ah80 t as80 / rd, / wr / cs1 ( cs2 ) d/i t pw h 80(r) , t pw h 80(w) ** t pwl80(w) and t pwl80(r) is specified in the overlapped period when cs1b is low (cs2 is high) and /wr(/rd) is low. parallel interface (8080-series mpu) timing diagra m ac characteristics (8080-series parallel mode) (v dd3 = 1.8 to 3.3 v, ta = - 30 to + 70 c) item signal symbol condition min. max. unit address setup time address hold time d/i t as80 t ah80 - - ns system cycle time t cy80 - ns pulse width low for write pulse width high for write wrb (wrb) t pwlw t pwhw - - ns pulse width low for read pulse width high for read rdb (rdb) t pwlr t pwhr - - ns data setup time data hold time t ds80 t dh80 - - ns read access time output disable time db0 to d b 15 t acc80 t od80 cl = 100 pf - ns note: *1. the input signal rise time and fall time (tr, tf) is specified at 1 0 ns or less. (tr + tf) < (t cy80 - t pwlw - t pwhw ) for write, (tr + tf) < (t cy80 - t pwlr - t pwhr ) for read 10/22 ver 1.0 6.4 instruction code instruction table instruction name d/i wrb rdb db15 ~ db8 db7 db6 db5 db4 db3 db2 db1 db0 hex. parameter non operation 0 0 1 * 0 0 0 0 0 0 0 0 00 oscillation mode set 0 0 1 * 0 0 0 0 0 0 1 0 02 1byte driver output mode set 0 0 1 * 0 0 0 1 0 0 0 0 10 1byte dc - dc select 0 0 1 * 0 0 1 0 0 0 0 0 20 1byte driving current & bias set 0 0 1 * 0 0 1 0 0 0 1 0 22 1byte dcdc clock division set 0 0 1 * 0 0 1 0 0 1 0 0 24 1byte dcdc and amp on/off set 0 0 1 * 0 0 1 0 0 1 1 0 26 1byte temperature compensation set 0 0 1 * 0 0 1 0 1 0 0 0 28 1byte contrast control(1) 0 0 1 * 0 0 1 0 1 0 1 0 2a 1byte contrast control(2) 0 0 1 * 0 0 1 0 1 0 1 1 2b 1byte sta ndby mode off 0 0 1 * 0 0 1 0 1 1 0 0 2c - standby mode on 0 0 1 * 0 0 1 0 1 1 0 1 2d - ddram burst mode off 0 0 1 * 0 0 1 0 1 1 1 0 2e - ddram burst mode on 0 0 1 * 0 0 1 0 1 1 1 1 2f - addressing mode set 0 0 1 * 0 0 1 1 0 0 0 0 30 1byte row vector mode set 0 0 1 * 0 0 1 1 0 0 1 0 32 1byte n - line inversion set 0 0 1 * 0 0 1 1 0 1 0 0 34 1byte entry mode set 0 0 1 * 0 1 0 0 0 0 0 0 40 1byte x - address area set 0 0 1 * 0 1 0 0 0 0 1 0 42 2byte y - address area set 0 0 1 * 0 1 0 0 0 0 1 1 43 2byte ram skip area set 0 0 1 * 0 1 0 0 0 1 0 1 45 1byte display off 0 0 1 * 0 1 0 1 0 0 0 0 50 - display on 0 0 1 * 0 1 0 1 0 0 0 1 51 - specified display pattern set 0 0 1 * 0 1 0 1 0 0 1 1 53 1byte partial display mode set 0 0 1 * 0 1 0 1 0 1 0 1 55 1byte partial display start line set 0 0 1 * 0 1 0 1 0 1 1 0 56 1byte partial display end line set 0 0 1 * 0 1 0 1 0 1 1 1 57 1byte area scroll mode set 0 0 1 * 0 1 0 1 1 0 0 1 59 4byte scroll start line set 0 0 1 * 0 1 0 1 1 0 1 0 5a 1byte set display dat a length x x x * 1 1 1 1 1 1 0 0 fc 1byte display data write 1 0 1 display data write - - display data read 1 1 0 display data read - - status read 0 1 0 0 status data read - - test mode1 0 0 1 * 1 1 1 1 1 1 1 1 ff - test mode2 0 0 1 * 1 1 1 1 1 1 1 0 f e - test mode3 0 0 1 * 1 1 1 1 1 1 0 1 fd - test mode4 0 0 1 * 1 1 1 1 1 0 1 1 fb - test mode5 0 0 1 * 1 1 1 1 1 0 1 0 fa - test mode6 0 0 1 * 1 1 1 1 1 0 0 1 f9 - *: don ? t care parameter: the number of parameter bytes that follows instruction data. 11/22 ver 1.0 7. optical characteristics 7.1 optical characteristics v lcd =16.8v ta=25 ?? item symbol condition min. typ. max. unit | x | y =0 ?? -40 -- +35 viewing angle | y c r 2 | x =0 ?? -30 -- +30 deg contrast ratio c r | x =0 ?? | y =0 ?? 30 - - turn on t on - - 200 response time turn off t off | x =0 ?? | y =0 ?? - - 100 ms x - 0.43 - red y | x =0 ?? | y =0 ?? - 0.35 - x - 0.32 - green y | x =0 ?? | y =0 ?? - 0.46 - x - 0.22 - color of cie coord- inate blue y | x =0 ?? | y =0 ?? - 0.26 - 12/22 ver 1.0 7.2 definition of optical characteristics 7.2.1 definition of viewing angle top top bottom bottom 7.2.2 definition of contrast ratio brightness state selected brightness state unselected = b2/b1 = ratio contrast measuring conditions: 1) ambient temperature: 25 ?? ; 2) frame frequency: 70.0hz 7.2.3 definition of response time turn on time: t on = t d + t r turn off time: t off = t d + t f measuring condition: 1) operating voltage: 16.8v 2) frame frequency: 70.0hz 13/22 ver 1.0 7.3 brightness characteristic item symbol condition min. typ. max. unit brightness bp 65 - - cd/m 2 uniformity ? bp ta=25 ?? 3 ?? 30-80%rh - - 60 % note: 1. the data is measured after leds are turned on for 5 minutes. 2. testing conditions led: v led = 10.0 (dc) lcd: all dots are on (white color) 3. brightness in the center of the lcd panel. 4. definition of uniformity ( ? bp) ? bp = bp (min.) / bp (max.) x 100 (%) bp (max.) = maximum br ightness in 9 measurement spots bp (min.) = minimum brightness in 9 measurement spots 14/22 ver 1.0 8. reliability 8.1 content of reliability test ta=25 ?? no. test item content of test test condition 1 high temperature storage endurance test applying the high storage temperature for a long time 80 ?? 2 ?? 240h restore 4h at 25 ?? 2 low temperature storage endurance test applying the low storage temperature for a long time -30 ?? 2 ?? 240h restore 4h at 25 ?? 3 high temperature /humidity storage endurance test applying the high temperature and high humidity storage for a long time 70 ?? 2 ?? 90%rh 240h restore 4h at 25 ?? 4 temperature cycle endurance test applying the low and high temperature cycle -30 ????? 25 ????? 80 ????? 25 ?? 30min 5min 30min 5min ??????????????? 1 cycle -30 ?? /80 ?? 10 cycles restore 4h at 25 ?? 5 vibration test (package state) endurance test applying the vibration during transportation 10hz~150hz, 100m/s 2 , 120min 6 shock test (package state) endurance test applying the shock during transportation half- sine wave, 300m/s 2 , 18ms 7 atmospheric pressure test endurance test applying the atmospheric pressure during transportation by air 25kpa 16h restore 2h 15/22 ver 1.0 8.2 failure judgment criterion test item no. criterion item 12 3 4 56789 failure judgement criterion basic specification out of the basic specification electrical specification out of the electrical specification mechanical specification out of the mechanical specification optical characteristic out of the optical specification note for test item refer to 8.1 remark basic specification = optical specification + mechanical specification 16/22 ver 1.0 9. quality level inspection examination or test at t a =25 ?? (unless otherwise stated) min. max. unit il aql external visual inspection under normal illumination and eyesight condition, the distance between eyes and lcd is 25cm. see appendix a ii major 1.0 minor 2.5 display defects under normal illumination and eyesight condition, display on inspection. see appendix b ii major 1.0 minor 2.5 note: major defects: open segment or co mmon, short, serious damages, leakage miner defects: others sampling standard conforms to gb2828 17/22 ver 1.0 10. precautions for use of lcd modules 10.1 handling precautions 10.1.1 the display panel is made of glass. do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 if the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 do not apply excessive force to the display su rface or the adjoining areas since this may cause the color tone to vary. 10.1.4 the polarizer covering the display surface of the lcd m odule is soft and easily scratched. handle th is polarizer carefully. 10.1.5 if the display surface is contamin ated, breathe on the surface and gently wipe it with a soft dry cloth. if s till not completely clear, moisten cloth with one of the following solvents: ?a isopropyl alcohol ?a ethyl alcohol solvents other than those men tioned above may damage the polarizer. especially, do not use the following: ?a water ?a ketone ?a aromatic solvents 10.1.6 do not attempt to disassemble the lcd module. 10.1.7 if the logic circuit power is off, do not apply the input signals. 10.1.8 to prevent destruction of the elemen ts by static electricity, be careful to maintain an optimum work environm ent. a. be sure to ground the body when handling the lcd modules. b. tools required for assembly, su ch as soldering irons, must be properly ground. c. to reduce the amount of sta tic electricity gene rated, do not conduct assembly and other work under dry c onditions. d. the lcd module is coated with a film to protect the display surface. be care when peeling off this protectiv e film since static electricity may be generated. 18/22 ver 1.0 10.2 storage precautions 10.2.1 when storing the lcd modules, avoi d exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 the lcd modules should be stored under the storage temperature range. if the lcd modules will be stored for a long time, the recommend condition is: te mperature : 0 ?? ?? 40 ?? relatively humidity: ? 80% 10.2.3 the lcd modules should be stored in the room without acid, alkali and harmful gas. 10.3 the lcd modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. 19/22 ver 1.0 appendix a inspection items and criteri a for appearance defects items contents criteria leakage not permitted rainbow according to the limit specimen wrong polarizer attachment not permitted not counted max. 3 defects allowed polarizer bubble between polarizer and glass <0.3mm 0.3mm ? 0.5mm scratches of polarizer according to the limit specimen not counted max. 3 spots allowed x<0.2mm 0.2mm ? x ? 0.5mm black spot (in viewing area) x=(a+b)/2 not counted max. 3 lines allowed black line (in viewing area) a<0.02mm 0.02mm ? a ? 0.05mm b ? 2.0mm max. 3 spots (lines) allowed progressive cracks not permitted 20/22 ver 1.0 appendix a inspection item and criteria for a ppearance defects (continued) items contents criteria a b c ? 3mm ? w/5 ? t / 2 cracks on pads ? 2mm ? w/5 t/2 22/22 ver 1.0 appendix b inspection items and criteria fo r display defects (continued) items content criteria not counted max. 2 defects allowed x ? 0.1mm 0.1mm ? x ? 0.2mm x=(a+b)/2 not counted max. 1 defects allowed a ? 0.1mm 0.1mm ? a ? 0.2mm d>0 max.3 defects allowed transfor- mation of segment max.2 defects allowed 0.8w ? a ? 1.2w a=measured value of width w=nominal value of width |
Price & Availability of TM128160EKFWGSPEC
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |